Friday, 30 August 2013

Capri - Jimboomba Auto Extravaganza, Sunday 25 August


This event was sponsored by the Early Ford V8 Club and was held at Maclean Bridge in Tully Park, Jimboomba. As well as the swap meet, you can either display your car or enter it into the judging competition. I decided that it was time my white 1972 Capri XL had a run so I cleaned it up and took it out on what was a great Sunday morning.
The swap meet had many stalls but, as usual, I didn’t see any Capri or small Ford parts. It looked like many of the stall holders had cleared out their sheds and brought the junk along to try and sell it. I didn’t buy anything.  There weren’t a huge number of cars on display but there were some really nice early Fords, including several Customlines.  Some really nice Ford Hot Rods were lined up with one done out like an American sprint car. Also, the usual nice Falcon GTs and Mustangs were present. The English Fords were represented by a couple of well-known Escorts, several Zephyrs and the lone white Capri XL.
 

Saturday, 24 August 2013

Capri - Car Quiz

This quiz, How well do you know your car?, was in today's Brisbane Courier Mail.
The author, Neil Dowling, asks whether the modern motorist is losing touch with the car.
It is pretty easy for most enthusiasts but I was completely incorrect with Question 13. See how you go.


These three funny stories were also on the page. The first one is a beauty and I can really relate to the last one as my eldest daughter tried to do exactly this with her first car.

Tuesday, 13 August 2013

Capri - Exhaust Manifold Flange

Owning a classis car means frequent maintenance and that is part of the fun! Maybe! The green Capri started to sound a bit like a tractor last week and a hand near the exhaust/manifold joint revealed an unwanted exhaust gas leak. If my memory is correct, the exhaust pipe had a very small crack in it where it fits into the manifold. So, off to buy an exhaust bandage and some muffler putty. getting the flange off wasn't a great problem but the two nuts are getting worn so I decided to replace them. (These pictures show the flange on loosely)



That was the hard part. I thought they were 3/8 inch UNC and they fitted the bolts at the local hardware store but on trying them on the car, they were not quite right. I tried numerous spare nuts but none seemed to be the correct fit. So off to the local bolt specialist & after a bit of trial & error decided the best fit were some metric nuts, about 5mm.  You never know what is on some old cars!
I wrapped the bandage around the joint, put some putty on top and then tightened everything up. After running the motor for about 10 minutes, it all seems good so we will wait and see after a decent trial run.

Friday, 9 August 2013

Capri Oil Filters

These comments refer to the 1600 Kent engine only. I have discussed this on occasions with other 1600 owners and there are a number of different points of view. I have experienced a few problems in stopping the oil filter from leaking on my green Capri. At present, it is not leaking and I am using a Repco oil filter on it, tightened to the extreme. This car has the 69IM engine block while my white XL 1600 has the 71IM block. I do not have the same problems with the XL. After discussions with other owners, I have learnt that the oil pump on the 69IM has a different type of connection area to the 71IM. There is a small ridge around the circumference on the 69IM which may reduce a good seal being made with the rubber seal on the oil filter. Some owners have ground off the ridge or even replaced the oil pump to solve this problem. At present I have a collection of three spare filters so I have had a good look at this seal area.
 
The three brands are (from the left): Repco ROF-22; Ryco Z62; Motorcraft AFLE227 (I managed to find this on EBay last year). There also was a Valvoline VO32 available but I have not seen one recently.
If the top area is examined carefully there are differences.
 



Firstly, it is obvious that the Ryco has a smaller inner diameter (57mm) than the other two and the seal is thinner (4mm). It also has a higher metal ridge on the inner side of the seal. The Motorcraft has a diameter of (62-63mm) and a seal width of 5 mm. The Repco has a diameter of 62 mm and a 6 mm seal width. I now understand why the Ryco, which is the one that is the easiest to obtain, is possibly the most unsuitable for the 69IM block as the smaller inner diameter is catching on the ridge. I have not had the filter off my car to accurately measure it on the pump but next time I will check it out.
So, the moral of this little story is - just check the oil filter seal measurements before you replace it, if you are having a problem with it leaking.
I would welcome any comments on this matter.

Friday, 26 July 2013

Capri Heater - No, Subaru Heater, Part 1

My Capris have been a little neglected for the last week or so as my attention has been directed to one of my other cars, a 1990 Subaru Liberty. This was originally my son's car but is used as a second daily driver. It is a really good car but not worth a great deal and for some months the heater has been leaking slightly into the interior of the front left hand side carpet. From past experience with Capris, I know what a terrible job it is & I knew that if it was to be done in a service centre, it would possibly cost about half the car's worth. So, after reading the manual & a fair bit of research on the web, I got to it. The pictures really tell the story from as it was to finding the heater.

[Click on the pictures if you want to see the real damage!]

Some words of advice - DON'T EVER DO THIS!! BYPASS THE HEATER OR SELL THE CAR!
This would have to be one of the worst car projects I have ever undertaken. Just as well I am retired as it took nearly two full days to get to the heater. Just when you thought the dash board could be lifted out, there was another wire to undo or unclip. It was just a maze of wires. The heater box, which is the larger white box in the centre was leaking from several places & it is right at the top in the centre of the dash.  Seeing the car is 23 years old, I suppose that is not too bad.
After a bit of research & phone calls, I went to the Valley Radiator Works, where Jim was most helpful. They were unable to source a new replacement part but repaired the old one with limited guarantee. That was done in a day & I could certainly recommend their service.
Putting it back together was just a painful & the main concern I had related to the after market car immobiliser fitted to the car. I was determined not to rush it, but again it took me nearly two days getting it back together. A few dramas resulted when you can't find a wire to connect up but eventually it was all back together. I also did a few other jobs at the same time while the battery was out like replacing the valve cover gaskets & spark plugs but that is another story.
I sought advice from the manufacturer about the alarm before I attempted to start it. Would it start or would windows go up & down instead of lights or mirrors? It fired up first go but there were lights flashing & indicators going everywhere. What the hell? I then realised that various switches were on & after turning these off, everything settled down. Yes, everything was working as it should, except as the car warmed up, I realised the heater was on when it was supposed to be off. The cable connecting the dash controls & the heater box had separated so I reached under the dash & turned off the heater which was a very simple fix but I will have to redo that bit. It doesn't require a huge amount of work. Overall, I was very happy to get it back together & working but would I do it again - I don't think so.
In Part 2 of the story, I will show you the Capri heater box & do a little comparison.

Capri Heater - Part 2

These are the pictures taken when I restored the Capri. Things were a lot less complicated in 1970 compared to the Subaru of 1990 (20 years difference). Whilst the heater box is still a metal or plastic box with a radiator & various flaps, the Subaru has heaps more wires & is connected to the air conditioning controls. They both require you to be an acrobat when trying to work on them but the Subaru was built around the heater box by Japanese people with small hands & standing on their heads! I wonder what a new 2013 Subaru Liberty or Audi would be like to work on - that is another 23 years difference.



When I did this I used a number of things that I have learnt in restoring the Capris, such as:
1. Before you even start, get a workshop manual and do as much research on the internet as you can. There were a number of illustrated stories from others who had done the same with their Subaru. I also got very extravagant and bought myself an Ozito lithium screwdriver for $30 from Bunnings which was great for this job. 
2. Don't underestimate the time something like this takes. Even the manual can make things sound not too difficult, like, unclip the wiring from the back of the dash board. This took me about an hour, using mirrors, small screwdrivers and with arms & hands caught in narrow spaces. Train an octopus!
3. Have loads of patience, a good back, a flexible neck, good eyesight & good hearing. I have none of these & when my hearing aides whistle, or my glasses fog up, or my back & neck ache, it is time for a Kit Kat!
4. Take heaps of pictures & at every stage. I constantly was referring back to these when I was re-assembling & I wish, in some instances, that I had taken more. I had to confirm one wiring connection (rear window demister) was missing & I finally found it due to the colour in the photo.
5. Label all the wiring & connectors. I usually use masking tape wrapped around the wire with where it goes. The Subaru was made a little easier with each connection having it own colour & type of connection that made it impossible to connect the wrong wires. This car had extras such as the immobiliser & spot lights which made it more fun!
6. Keep all the screws for each section together. I use envelops or plastic bags & label them. eg radio. I also tape clips & screws to the trim that they come from. I though I did pretty well but ended up with 4 extra screws from the radio area. I have no idea where these went!
7. When you think you have finished, make another check. With the heater, I had to drain all the radiator fluid & then make sure all the clamps & hoses were tight & correct.
8. After everything is back together & working, reward yourself by running around the yard naked, yelling " It's finished! It's finished!" Well, perhaps a coldie might be more appropriate or for me, it's a heat pack on my back! I'll never do it again-until the next time.

Saturday, 20 July 2013

Capri - RACQ Motorfest, Brisbane



This is one of the big car shows in Brisbane & in excess of 700 classics were to attend last weekend (14 July). Unfortunately, the day started not too well, weather wise and a number of entrants chose to stay at home. Whilst it remained overcast the rain stayed away for most of the day.
My Capri was the only one there this year and it is surprising how much interest there is in these cars. Many people who grew up in the UK always want to have a chat about the Capri. There was a great display of Cortinas and one took the award for the category.
As can be seen by the photos, there is a very diverse range of vehicles which include Australian, British, American, European, Japanese, Speedway, Military & Commercial. It was also a special anniversary event for Aston Martin & Lamborghini.