Friday, 1 May 2020

Capri - Fuel Tank Cleaning

Last week I went to take advantage of cheap petrol prices and fill up my white XL. Unfortunately, it seems it has caught the virus!!! It was running so badly I didn't even get to the servo. It seems that not been driven for a few weeks has revived a chronic problem I seem to have with this car & that is that it seems not to like contaminated fuel. It may have got water in the tank or the carbie, whichever, it seems to be a fuel problem and is running badly.
After several hours of procrastinating as to why I shouldn't drain the fuel and/or clean the tank, I decided to drain the tank & then see what the fuel was like.
Step 1: Drain the tank. I siphoned the fuel out, about 10 -12 litres, into a bucket. I was rather shocked at the colour of the fuel. It looked black, not the usual colour I expected. That made the decision for me. The tank has to come out & be cleaned - maybe the first time in 48 years.



Step 2: Disconnect the rubber hose between the tank & the fuel filler. This would rate as one of the worst jobs to do on a Capri. The manual says to undo the screws (4) holding the filler pipe. If you do this first, you cannot really twist the rubber hose on that end to the extent you need to. After undoing the clips & copious amounts of RP7, I final had the hose moving a little but not enough to move it along back up the filler to disconnect. I walked away about 3 times. Come back & more spray. When I did get it moving a little, I undid the fuel filler screws & then I was able to turn the hose around a little more. More spray & then some detergent, more twisting & finally using various tools, screw drivers, I was able to move the hose off at the tank outlet. Don't be in a hurry to do this job as it will drive you crazy, not too mention where the hose is and the body contortions necessary to reach it.



Step 3: Disconnect the vent hose that runs along the top of the tank. It comes off the vent pipe with a bit of pulling.



Step 4: Get your longest socket + extension bar with a half inch socket and undo the top two nuts holding the tank. With the long bar it wasn't too difficult. The 2 bottom bolts are very easy.
Step 5: Just move the RHS of the tank out enough to be able to disconnect the fuel line + the wire for the fuel gauge. They both come off without too much trouble. Then remove the tank.



Step 6: Mark the sender unit & the tank to ensure they match up when putting it back together. With a large set of shifters or a Stillson wrench, remove the unit, ensuring that the float does not get damaged on the way out. There is an arrow on the sender unit indicating which way to turn the unit. The filter which may be an original looked pretty dirty and I am not sure how I will clean this or even replace it.



Step 7: The cleaning of the tank - I was surprised that the inside of the tank was as clean as it was. I was expecting a lot of sludge, but none. I poured in a bucket of warm water plus some detergent & then used a pressure spray to rinse out the inside. After several rinses, it seemed OK & I left it to dry.
Step 8: A quick paint touch up of the tank plus the area behind the tank in the trunk area.
Step 9: I located a Mustang fuel sender filter ($8) which I thought I could modify to fit the tank. With some super strength Araldite, I attached the new filter to the old top so it would fit tightly onto the fuel pipe.
Step 10: A complete cleanout of all the fuel lines & the carbie jets using compressed air & carbie cleaner.
Step 11: Fitted a new fuel filter between the fuel pump & the carbie.



Step 12: Refitted the tank, fuel hose & fuel gauge wire. The top two nuts for the tank are not easy! I used a magnetic tool to attach the washers & then the long handled socket with the nut in the socket to screw up the tank. A bit of mucking about but they eventually went on.
Step 13: THE WORST JOB OF ALL THINGS ON A CAPRI - FITTING THE HOSE BETWEEN THE TANK & THE FILLER PIPE. Nothing could be worse than this. I have had people say just put a bit of detergent on the connection areas & it slides on. Not in my experience! I tried everything & could not get it on the filler pipe. I eventually put the filler end in some very hot water for a few minutes & eventually got it on & then was able to slide it back over the tank pipe. Very difficult for me & I was stuffed. Tightened up one clamp but did not have the energy to finish the second one. I hope this is all worth it & the car runs OK. Finished the job today. Much easier after a night's sleep. Checked all the hoses.
Step 14: With some fresh Shell V-Power in the tank, will it start? Yes, and without too much trouble and the fuel gauge still works. No apparent leaks. The engine is running OK & I will not say too much more until after a road test which we are allowed to do this weekend. One think is for sure is that the fuel system is clean.
PS. Finally able to take the car out again and it went really well, thank goodness!
[Click on photos to enlarge]

Thursday, 9 April 2020

Capris in Isolation

Even the Capris are having to isolate. Mine don't seem to understand that they have to be 1.5 metres apart.😷😊
Have the best possible Easter!

Friday, 3 April 2020

Capri - Bonnet Catch Adjustment

Being partially isolated due to the pandemic has meant a bit more time to do some maintenance tasks on the Capris. Next on the list was to adjust the bonnet catch on the green Deluxe. The bonnet has a rare habit of popping up when you least expect it. Thankfully, the safety catch works & prevents the bonnet from lifting right up. On a recent run over some country roads, the bonnet popped twice. I have a theory that when the body flexs a little on bends or bumps, the catch releases.
The first thing I did was measure the height of both the bump stops & the bonnet catch with the spring. I then wound back the RHS bump stop a few mm to even it up with the LHS. Next was to see if the rod was entering the bonnet catch correctly. Using some masking tape, it seemed as if this was all good.


Then to lengthen the pin/rod so it would fit more securely into the catch. That's when the difficulty started. The pin/rod would not turn even after the spring locking nut had been released. No matter how hard I tried & with different large screwdrivers, it would not budge. I guess it hadn't been moved for 50 years. OK, out with the RP7 & Inox. Much spraying at different times & still no movement. I ended up leaving it for the day & came back the next day & continued spraying & trying to undo it. Finally, with a spanner clamped onto the screw driver, I got a little movement. Working it back & forward slowly finally cracked it & then it started to undo.
The whole bonnet pin assembly looked like it hadn't been cleaned for many years so it was taken apart & cleaned up.



Then everything back on & with a few adjustments, it all looks good. Let's wait for the final comment after a bit of driving.

Wednesday, 1 April 2020

Capri - Oil Filer Problems

It was time for an oil change on the green Deluxe. The oil filter was also due for a change & and I did remember that last time the only filter brand that would fit was the Repco ROF-22. I contacted Repco to see if they were still available and was told that a store near me had 3 in stock so off to the store and I bought one for $17.55.
Oil drained & old filter (ROF-22) removed with no dramas. I took the new one out of the carton and it was very different - longer and with a completely different O ring set up. I then started to remember all the problems I had last time & why I just put the old one back on. Put the new on and screwed it up tight, started the car & oil spewed out on the floor from the filter. Not very happy!!


 I decided to go back to Repco to see if the other 2 filters they had in stock were the same. The lady brought one back & it was completely different, very similar to old one I had taken off, so I was very happy about that. At home, looking at the two satisfied me that they were the same so I put the second new one. Started the engine & more oil spewed out everywhere! What is going on? The photos show how similar they are.

 

This car (1970) has the 691M crossflow motor which has a different oil filter set up to the later 711M engine. the earlier car originally had a cartridge type filter but the later screw on types usually fit. A really close examination of the new filter would suggest that the inner circular metal lip is fouling on the inner ridge of the oil pump. It gives the impression that the new filer is on tight but it really has not sealed at all. What to do?
For the moment, I cleaned the old filter as best as I could, screwed it back on, started the car and no leaks at all.
I then checked my white XL (1972  & 711M engine) & it has a Motorcraft AFLE 227 filter which I picked up on eBay a while back. Time to check out all my spare parts bins. here I found an old oil pump (691M) type (I have no idea where it came from) & another new Repco ROF-22 filter. Great! I could really see why these filters were not fitting with an oil pump off the engine.
When I opened the oil filter box, it was the type that was longer & with a wide, flat O ring. On measuring the diameter, one could see that the inner metal lip was catching & not allowing the filter to seal. The lip was turned over slightly. After much dreaming, my theory was that if I could grind the  turned section of the lip off, it should slide over the ridge on the oil pump. So with a small grinding stone on my drill, I worked my way around the lip and ground until it was straight. I tried it on the pump and yes, it tightened all the way up. At last I think this will solve the problem. Here is the filter after being altered.



Now, to see if this one fits & doesn't leak. Screwed it on & it goes all the way up and the rubber seal is right on the oil pump. Tightened it up. Started the engine & thankfully, no oil leaking out. I hope I don't have to do this each time a filter is replaced but it is most that is what will happen.
So, the moral of the story is, as always with old cars - don't throw away old parts until you are sure the new one fits correctly
As far as Repco ROF-22 filters, I have had 3 on the car and they are all different so all oil filters are not necessarily the same.
(click on the photos to enlarge)

Tuesday, 17 March 2020

Capri - LUCH Quartz Car Dashboard Clock Round

Yes, the title says it all!
For quite some time I have been looking for a suitable classic looking clock to fill the hole in my centre console. Actually, a non functioning amp meter has been there for several years. Being a cheapskate, I refused to pay the amounts being asked for some brands but I kept seeing the LUCH clock on eBay for a very reasonable price. Apparently there is quite a story to the LUCH factory as it has along history in Soviet Russia but has modernised in Minsk, Belarus.
With a little concern I ordered the clock on eBay. It arrived all packaged in under 2 weeks for the pricely sum of $25.04 including postage & GST. Instructions were printed in English. Even a postcard of the River Minsk was included. Here are some pics.

 
So, I eventually got around to fitting it.
I took the easy way and used the connections I had removed from the cigarette lighter to power up the clock & the light for it. These are just to the LHS of the ashtray so all I had to do was remove the ash tray & the small cardboard panel to the RHS of the ash tray to give me enough access to wire it up in the central console. A dilemma I had was that I really didn't want to have the clock continuously live wired as the car is not driven very often. This may defeat the purpose of have a clock but it is my preference and will operate only when the ignition is turned on. This means a quick reset of the clock each time I drive the car but it is no big deal.
One of the wires powers the clock & the other powers the light. The earth wire I ran back to the nut that holds the ash tray in place. I also included a 10 amp fuse in power wire. Here are some pics.
 

As you can see the clock fits in really neatly with no alterations needed and is a firm fit. It is similar in colouring to the other Capri instruments. At the advice on club members, I have ensured the clock has no tracking devices that would benefit the KGB! It works well, with a very quiet movement and I think very good value.

Monday, 16 March 2020

Capri - Poor Idling

My white XL Capri has not been running very smoothly of late, especially idling roughly.
I did the usual things like checking all the leads and connections but no difference. With the engine running, I started pulling off the ignition leads & to my surprise when I removed the lead to No 1 cylinder, it made no difference. When the other cylinder leads were removed, you could really notice the difference. So, it was No 1 cylinder that was the problem.
First fix was to replace the ignition leads & the spark plugs. The leads had not been replaced in a long while so I thought replacing both of these items would fix the problem.



So with the new ones in place, I started the engine & no real difference. Pulling the lead from No 1 cylinder when idling & again it made no difference. So, what was the problem? I had read that air leaks around the inlet manifold may be an issue but after checking all the hoses & connections, again there was no difference.
Then looking around again with a torch, I noticed that the inlet manifold gasket was split right on the end near the No 1 cylinder inlet port. It was like a tear in the gasket. So was this the problem? The only way to find out was to replace the gasket. The photos show the damaged gasket as the split went right through the edge of the gasket. Look at the right hand lower section of the gasket. On removal of the manifold, it seem as if the gasket was also covering part of the inlet port.

 

Removing the inlet manifold is a real pain!!! The two bolts underneath require a narrow socket to remove them. What made mine really difficult was that last time I had the manifold off I had to replace the centre bottom bolt with a different size head (the other 4 are all 1/2 inch). After spending ages to work this out, it soon came out with the correct size socket.
Luckily I had a spare ACL gasket so on it went. Again, tightening the bolts underneath is not all that easy. So, after reconnecting everything, refilling the radiator as when the manifold came off, a bit of fluid was lost around the water jacket.
OK, now time to turn the key. Yes, much smoother & running really well and idling much better.I did not realise that such a split would allow so much air to enter the system and cause it to run roughly.
End of story so make sure you check for air leaks if your car is sounding a bit sick.
(Click on the photos to enlarge)